.: Cisco CCNA / CCNP Certification Exam Tutorial: Configuring PPP Callback
Category:Home / Computers / Computer Certification
You may run into situations where a router in a remote location needs to dial in to a central router, but the toll charges are much higher if the remote router makes the call. This scenario is perfect for PPP Callback, where the callback client places a call to a callback server, authentication takes place, and the server then hangs up on the client! This ensures that the client isn't charged for the call. The server then calls the client back.
In the following example, R2 has been configured as the client and R1 is the callback server. Let's look at both configurations and the unique commands PPP Callback requires.
Client:
username R1 password CCIE
interface BRI0
ip address 172.12.12.2 255.255.255.0
encapsulation ppp
dialer map ip 172.12.12.1 name R1 broadcast 5557777
dialer-group 1
isdn switch-type basic-ni
ppp callback request
ppp authentication chap
Most of that configuration will look familiar to you, but the ppp callback request command might not. This command enables the BRI interface to request the callback.
Simple enough, right? The PPP Callback Server config requires more configuration and an additional map-class as well.
Server:
username R2 password CCIE
interface BRI0
ip address 172.12.12.1 255.255.255.0
encapsulation ppp
dialer callback-secure
dialer map ip 172.12.12.2 name R2 class CALL_R2_BACK broadcast 5558888
dialer-group 1
isdn switch-type basic-ni
ppp callback accept
ppp authentication chap
map-class dialer CALL_R2_BACK
dialer callback-server username
Examining the PPP Callback Server command from the top down...
dialer callback-secure enables security on the callback. If the remote router cannot be authenticated for callback, the incoming call will be disconnected.
The dialer map statement now calls the class CALL_R2_BACK, shown at the bottom of the config excerpt.
ppp callback accept enables PPP callback on this router.
dialer callback-server username tells the callback server that the device referenced in the dialer map statement is a callback client.
The only way to find out if the config works is to test it, so let's send a ping from R2 to R1 and see if the callback takes place.
R2#ping 172.12.12.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.12.12.1, timeout is 2 seconds:
02:45:42: BR0 DDR: Dialing cause ip (s=172.12.12.2, d=172.12.12.1)
02:45:42: BR0 DDR: Attempting to dial 5557777
02:45:42: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
02:45:42: BR0:1 DDR: Callback negotiated - Disconnecting now
02:45:42: BR0:1 DDR: disconnecting call
02:45:42: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 5557777 R1
02:45:42: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
02:45:42: DDR: Callback client for R1 5557777 created
02:45:42: BR0:1 DDR: disconnecting call.....
Success rate is 0 percent (0/5)
R2#
02:45:57: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
R2#
02:45:57: BR0:1 DDR: Callback received from R1 5557777
02:45:57: DDR: Freeing callback to R1 5557777
02:45:57: BR0:1 DDR: dialer protocol up
02:45:58: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to up
The callback was successfully negotiated, and the call then disconnected. R1 then called R2 back, and show dialer on R1 confirms the purpose of the call.
R1#show dialer
BRI0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
5558888 2 4 00:00:20 successful
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI0:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is data link layer up
Dial reason: Callback return call
Time until disconnect 99 secs
Connected to 5558888 (R2)
Pretty cool! PPP Callback isn’t just important for passing your CCNA and CCNP exams – in circumstances such as shown in this example, it can save your organization quite a bit of money!
Article keywords: ccna, ccnp, free, exam, ppp, callback, isdn, caller, client, server, pass, bcran, tutorial, bryant
Article Source: http://www.articles32.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, visit the website and download your free copies. You can also get FREE CCNA and CCNP exam questions every day! Get your CCNA study guide from The Bryant Advantage! And coming in 2007 – Microsoft Vista certification!
.: New Computer Certification Articles
1). Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address
To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this tutorial.
We've got two routers on a segment running HSRP, so first we need to find out what the MAC address of the HSRP virtual router is.
2). Cisco CCNP Certification / BSCI Exam Tutorial: An Introduction To BGP
When you're studying for the BSCI exam on the way to earning your CCNP certification, it's safe to say that BGP is like nothing you’ve studied to this point. BGP is an external routing protocol used primarily by Internet Service Providers (ISPs). Unless you work for an ISP today or in the future, you may have little or no prior exposure to BGP. Understanding BGP is a great addition to your skill set – and you have to know the basics well to pass the BSCI exam.
3). Cisco CCNA Certification Exam Tutorial: Distance Vector Command Review
Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very important distance vector and static routing commands you need to know, along with their proper usage and console output.
4). Cisco CCNA Certification Exam Tutorial: Keep Your Most Important Appointment
Imagine this. You have an appointment with a client to work on a server or router install. A few minutes before you're scheduled to be there, you decide there's something really good on TV you'd like to watch. Or you decide to go to the gym, or play a game, or do anything else except go see the client.
Even if you weren't going to get fired for not showing up, it's certainly unfair to the client.
5). CCNP Certification / BSCI Exam Tutorial: The BGP Neighbor Process
Like TCP, BGP is connection-oriented. An underlying connection between two BGP speakers is established before any routing information is exchanged. This connection takes place on TCP port 179. As with EIGRP and OSPF, keepalive messages are sent out by the BGP speakers in order to keep this relationship alive.
Once the connection is established, the BGP speakers exchange routes and synchronize their tables.
6). CCNP Certification / BCMSN Exam Tutorial: Server Load Balancing (SLB)
When you're working on your BCMSN exam on your way to CCNP certification, you'll read at length about how Cisco routers and multilayer switches can work to provide router redundancy - but there's another helpful service, Server Load Balancing, that does the same for servers. While HSRP, VRRP, and CLBP all represent multiple physical routers to hosts as a single virtual router, SLB represents multiple physical servers to hosts as a single virtual server.
7). CCNA / MCSE / CCNP Certification: Making Failure Work For You
Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're going to fail an exam. It's happened to almost all of us, yours truly included. What you have to keep in mind in these times is that success is not a straight line. You've probably seen charts showing the growth of an industry or a business -- you know, the ones that go from left to right, and look kind of jagged.
.: Top Computer Certification Articles
1). Cisco CCNP / BSCI Exam Tutorial: OSPF Route Redistribution Review
OSPF route redistribution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route redistribution basics.
To see if a router is an ABR or ASBR, run show ip ospf. This also displays any routes being redistributed into OSPF on this router.
2). Cisco CCNA Certification Exam Tutorial: Variance And Unequal Cost Load Balancing
To pass the CCNA exam, you've got to know how to work with IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure that all paths are in use while allowing for varying bandwidth rates.
Using the variance command is the easy part - it's getting the metric that's the hard part with IGRP.
3). Cisco CCNA Exam Tutorial: Route Summarization
Preparing to pass the CCNA exam and earn this important Cisco certification? Route summarization is just one of the many skills you'll have to master in order to earn your CCNA. Whether it's RIP version 2, OSPF, or EIGRP, the CCNA exam will demand that you can flawlessly configure route summarization.
Route summarization isn't just important for the CCNA exam.
4). Cisco CCNA / CCNP Home Lab Setup: How To Configure Reverse Telnet
Occasionally, during your CCNA and CCNP studies, you'll run into a term that just doesn't quite make sense to you. (Okay, more than occasionally!) One such term is "reverse telnet". As a Cisco certification candidate, you know that telnet is simply a protocol that allows you to remotely connect to a networking device such as a router or switch. But.
5). Cisco CCNA / CCNP Home Lab Tutorial: Configuring An Access Server
As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we'll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS.
Here's part of a configuration from one of my access servers:
ip host FRS 2006 100.
6). Cisco CCNA Certification: Defining Broadcast Domains
When you're studying to pass the CCNA exam and earn your certification, you're introduced to a great many terms that are either totally new to you or seem familiar, but you're not quite sure what they are. The term "broadcast domain" falls into the latter category for many CCNA candidates.
A broadcast domain is simply the group of end hosts that will receive a broadcast sent out by a given host.
7). Passing Your CCNA and CCNP: Configuring And Troubleshooting Router-On-A-Stick
For CCNA and CCNP candidates, it's hard not to laugh the first time you hear the phrase "router on a stick". Let's face it, that's a pretty silly term. But as those who have passed the CCNA and CCNP exams know, this is a vital exam topic that you must know how to configure and troubleshoot.
Basic Cisco theory states that for hosts in different VLANs to communicate, a Layer 3 device must be involved to handle the routing between the VLANs.