.: Cisco CCNA / CCNP Certification Exam Tutorial: Floating Static Routes
Category:Home / Computers / Computer Certification
To pass the Cisco CCNA and CCNP certification exams, as well as becoming a world-class networker, you've got to know how and when to use floating static routes. And if you're wondering what makes them "float" -- read on!
In this example, R1 and R2 are running OSPF over a Frame Relay network, 172.12.123.0 /24. They're also connected by a BRI ISDN link, 172.12.12.0 /24. R1 is advertising a loopback network, 1.1.1.1 /32, via OSPF. We want R2 to have a route to that loopback even if the frame goes down - and here, we'll use a floating static route to make that happen.
R2 sees the route to the loopback interface via OSPF, and can ping that interface successfully.
R2#show ip route ospf
1.0.0.0/32 is subnetted, 1 subnets
O 1.1.1.1 [110/65] via 172.12.123.1, 00:00:02, Serial0
R2#ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 68/68/68 ms
This is when it's important to know your administrative distances.... or at least know where to look to see them! The AD of OSPF is 110, which means we can configure a static route to 1.1.1.1 /32, and as long as the AD of the static route is higher than 110, it won't be used unless the OSPF route leaves the routing table. That's why this kind of route is called a "floating" static route - the route "floats" in the routing table and isn't seen unless the primary route leaves the table.
You learned how to write a static route in your CCNA studies, but you also remember that the default AD of a static route is either 1 or 0... and both of those values are less than 110! To change the AD of a static route, configure the desired distance at the end of the ip route command.
R2(config)#ip route 1.1.1.1 255.255.255.255 bri0 ?
<1-255> Distance metric for this route
A.B.C.D Forwarding router's address
name Specify name of the next hop
permanent permanent route
tag Set tag for this route
R2(config)#ip route 1.1.1.1 255.255.255.255 bri0 111
The static route has an AD that's only one higher than that of the OSPF route, but that's enough to make the route "float" and not yet be seen in the routing table.
R2#show ip route
1.0.0.0/32 is subnetted, 1 subnets
O 1.1.1.1 [110/65] via 172.12.123.1, 00:06:44, Serial0
172.12.0.0/24 is subnetted, 2 subnets
C 172.12.12.0 is directly connected, BRI0
C 172.12.123.0 is directly connected, Serial0
Let's see the effect on the routing table when the Serial0 interface is closed.
R2(config)#int s0
R2(config-if)#shutdown
12:04:53: %OSPF-5-ADJCHG: Process 1, Nbr 172.12.123.1 on Serial0 from FULL to DOWN, Neighbor Down: Interface down or detached
12:04:55: %SYS-5-CONFIG_I: Configured from console by console
12:04:55: %LINK-5-CHANGED: Interface Serial0, changed state to administratively down
12:04:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
R2#show ip route
1.0.0.0/32 is subnetted, 1 subnets
S 1.1.1.1 is directly connected, BRI0
172.12.0.0/24 is subnetted, 1 subnets
C 172.12.12.0 is directly connected, BRI0
The floating static route appears in the table, but the ISDN link will not come up until the BRI interface has traffic to send. Let's ping 1.1.1.1 and see what happens. debug dialer was configured on R2 before sending the ping.
R2#ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
12:16:01: BR0 DDR: Dialing cause ip (s=172.12.12.2, d=1.1.1.1)
12:16:01: BR0 DDR: Attempting to dial 8358661
12:16:01: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up.!!
12:16:01: BR0:1 DDR: dialer protocol up!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 36/37/40 ms
The link comes up and traffic can still reach 1.1.1.1. Once R2 becomes an OSPF neighbor of R1 again, the OSPF route will again become the primary path and the floating static route leaves the routing table.
R2(config)#int s0
R2(config-if)#no shut
R2#show ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
172.12.123.1 1 FULL/DR 00:01:57 172.12.123.1 Serial0
R2#show ip route
1.0.0.0/32 is subnetted, 1 subnets
O 1.1.1.1 [110/65] via 172.12.123.1, 00:00:16, Serial0
172.12.0.0/24 is subnetted, 2 subnets
C 172.12.12.0 is directly connected, BRI0
C 172.12.123.0 is directly connected, Serial0
A floating static route is an excellent "back door" that will keep the ISDN link down while allowing that link to serve as a backup route. Just make sure the ISDN link comes down when you expect it to - always check that with show isdn status!
Article keywords: ccna, ccnp, bcran, floating, static, route, ip, isdn, bri, pass, free, tutorial, lab, distance, AD
Article Source: http://www.articles32.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, visit the website and download your free copies. You can also get FREE CCNA and CCNP exam questions every day! And coming in 2007 -- Microsoft Vista certification from The Bryant Advantage!
.: New Computer Certification Articles
1). Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address
To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this tutorial.
We've got two routers on a segment running HSRP, so first we need to find out what the MAC address of the HSRP virtual router is.
2). Cisco CCNP Certification / BSCI Exam Tutorial: An Introduction To BGP
When you're studying for the BSCI exam on the way to earning your CCNP certification, it's safe to say that BGP is like nothing you’ve studied to this point. BGP is an external routing protocol used primarily by Internet Service Providers (ISPs). Unless you work for an ISP today or in the future, you may have little or no prior exposure to BGP. Understanding BGP is a great addition to your skill set – and you have to know the basics well to pass the BSCI exam.
3). Cisco CCNA Certification Exam Tutorial: Distance Vector Command Review
Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very important distance vector and static routing commands you need to know, along with their proper usage and console output.
4). Cisco CCNA Certification Exam Tutorial: Keep Your Most Important Appointment
Imagine this. You have an appointment with a client to work on a server or router install. A few minutes before you're scheduled to be there, you decide there's something really good on TV you'd like to watch. Or you decide to go to the gym, or play a game, or do anything else except go see the client.
Even if you weren't going to get fired for not showing up, it's certainly unfair to the client.
5). CCNP Certification / BSCI Exam Tutorial: The BGP Neighbor Process
Like TCP, BGP is connection-oriented. An underlying connection between two BGP speakers is established before any routing information is exchanged. This connection takes place on TCP port 179. As with EIGRP and OSPF, keepalive messages are sent out by the BGP speakers in order to keep this relationship alive.
Once the connection is established, the BGP speakers exchange routes and synchronize their tables.
6). CCNP Certification / BCMSN Exam Tutorial: Server Load Balancing (SLB)
When you're working on your BCMSN exam on your way to CCNP certification, you'll read at length about how Cisco routers and multilayer switches can work to provide router redundancy - but there's another helpful service, Server Load Balancing, that does the same for servers. While HSRP, VRRP, and CLBP all represent multiple physical routers to hosts as a single virtual router, SLB represents multiple physical servers to hosts as a single virtual server.
7). CCNA / MCSE / CCNP Certification: Making Failure Work For You
Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're going to fail an exam. It's happened to almost all of us, yours truly included. What you have to keep in mind in these times is that success is not a straight line. You've probably seen charts showing the growth of an industry or a business -- you know, the ones that go from left to right, and look kind of jagged.
.: Top Computer Certification Articles
1). Cisco CCNP / BSCI Exam Tutorial: OSPF Route Redistribution Review
OSPF route redistribution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route redistribution basics.
To see if a router is an ABR or ASBR, run show ip ospf. This also displays any routes being redistributed into OSPF on this router.
2). Cisco CCNA Certification Exam Tutorial: Variance And Unequal Cost Load Balancing
To pass the CCNA exam, you've got to know how to work with IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure that all paths are in use while allowing for varying bandwidth rates.
Using the variance command is the easy part - it's getting the metric that's the hard part with IGRP.
3). Cisco CCNA Exam Tutorial: Route Summarization
Preparing to pass the CCNA exam and earn this important Cisco certification? Route summarization is just one of the many skills you'll have to master in order to earn your CCNA. Whether it's RIP version 2, OSPF, or EIGRP, the CCNA exam will demand that you can flawlessly configure route summarization.
Route summarization isn't just important for the CCNA exam.
4). Cisco CCNA / CCNP Home Lab Setup: How To Configure Reverse Telnet
Occasionally, during your CCNA and CCNP studies, you'll run into a term that just doesn't quite make sense to you. (Okay, more than occasionally!) One such term is "reverse telnet". As a Cisco certification candidate, you know that telnet is simply a protocol that allows you to remotely connect to a networking device such as a router or switch. But.
5). Cisco CCNA / CCNP Home Lab Tutorial: Configuring An Access Server
As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we'll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS.
Here's part of a configuration from one of my access servers:
ip host FRS 2006 100.
6). Cisco CCNA Certification: Defining Broadcast Domains
When you're studying to pass the CCNA exam and earn your certification, you're introduced to a great many terms that are either totally new to you or seem familiar, but you're not quite sure what they are. The term "broadcast domain" falls into the latter category for many CCNA candidates.
A broadcast domain is simply the group of end hosts that will receive a broadcast sent out by a given host.
7). Passing Your CCNA and CCNP: Configuring And Troubleshooting Router-On-A-Stick
For CCNA and CCNP candidates, it's hard not to laugh the first time you hear the phrase "router on a stick". Let's face it, that's a pretty silly term. But as those who have passed the CCNA and CCNP exams know, this is a vital exam topic that you must know how to configure and troubleshoot.
Basic Cisco theory states that for hosts in different VLANs to communicate, a Layer 3 device must be involved to handle the routing between the VLANs.