.: Cisco CCNA Certification Exam Tutorial: Distance Vector Command Review
Category:Home / Computers / Computer Certification
Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very important distance vector and static routing commands you need to know, along with their proper usage and console output.
Bandwidth
IGRP makes a default assumption that any Serial interface running IGRP is connected to a T1 line, which runs at 1544 KBPS. With equal-cost load-balancing enabled by default, this may be an undesirable assumption.
To alter IGRP’s assumption, use the bandwidth command on the serial interface in question. Note that this command does NOT actually affect the bandwidth available to the interface; it merely changes IGRP’s assumption of the bandwidth.
R2#conf t
R2(config)#int s0
R2(config-if)#bandwidth 512
Clear ip route *
This command clears your routing table of all non-static and non-connected routes. In a lab environment, it’s very handy because it forces your routers running routing protocols to send and request updates, rather than waiting for the regularly scheduled updates.
R2#clear ip route *
Debug ip igrp events
Debug ip igrp events allows you to see IGRP updates being sent and requested. Here, the debug is run and then the routing table is cleared. The router immediately broadcasts update requests via the IGRP-enabled interfaces.
R2#debug ip igrp event
IGRP event debugging is on
R2#clear ip route *
06:02:51: IGRP: broadcasting request on BRI0
06:02:51: IGRP: broadcasting request on Serial0.123
Debug ip igrp transactions
To configure IGRP unequal-cost load-sharing with the variance command, you’ve got to know the metric of the less-desirable routes. EIGRP keeps these in its topology table; IGRP has no such table.
To get the metrics of routes not in the routing table, run debug ip igrp transactions. To force IGRP updates, the routing table below was cleared with clear ip route *.
R2#debug ip igrp transactions
IGRP protocol debugging is on
R2#clear ip route *
06:05:33: IGRP: received update from 172.12.123.1 on Serial0.123
06:05:33: subnet 172.12.123.0, metric 10476 (neighbor 8476)
06:05:33: network 1.0.0.0, metric 8976 (neighbor 501)
06:05:33: IGRP: edition is now 3
06:05:33: IGRP: sending update to 255.255.255.255 via BRI0 (172.12.12.2)
06:05:33: network 1.0.0.0, metric=8976
06:05:33: IGRP: sending update to 255.255.255.255 via Serial0.123 (172.12.123.2) - suppressing null update
06:05:34: IGRP: received update from 172.12.12.1 on BRI0
06:05:34: subnet 172.12.13.0, metric 160250 (neighbor 8476)
06:05:34: network 1.0.0.0, metric 158750 (neighbor 501)
Debug ip rip
R2#debug ip rip
IP protocol debugging is on
R2#clear ip route *
6:14:53: RIP: received v2 update from 172.23.23.3 on Ethernet0
6:14:53: 1.0.0.0/8 via 0.0.0.0 in 16 hops (inaccessible)
6:14:53: 1.1.1.1/32 via 0.0.0.0 in 2 hops
6:14:53: 172.12.0.0/16 via 0.0.0.0 in 16 hops (inaccessible)
6:14:53: 172.12.12.2/32 via 0.0.0.0 in 2 hops
6:14:53: 172.12.13.0/30 via 0.0.0.0 in 1 hops
6:14:53: 172.12.123.0/24 via 0.0.0.0 in 1 hops
6:14:53: 172.23.0.0/16 via 0.0.0.0 in 16 hops (inaccessible)
Run debug ip rip to troubleshoot routing update problems, RIP authentication problems, and to view the routing update contents. Clear ip route * was run to clear the routing table and to force a RIP update.
Ip route
R2#conf t
R2(config)#ip route 1.1.1.1 255.255.255.255 172.12.123.1
OR
R2(config)#ip route 1.1.1.1 255.255.255.255 serial0
To configure a static route to a given destination IP address, use the ip route command. The destination is followed by a subnet mask, and that can be followed by either the next-hop IP address or the exit interface on the local router.
Ip route 0.0.0.0 0.0.0.0
R2#conf t
R2(config)#ip route 0.0.0.0 0.0.0.0 172.12.123.1
OR
R2(config)#ip route 0.0.0.0 0.0.0.0 ethernet0
To configure a default static route, use either of these two commands.
You could have any number for the first “0.0.0.0", since the second set of zeroes is the subnet mask. This means that any destination will match this route statement.
That's a good review to get started with! I'll be back tomorrow with Part II of this CCNA exam command review!
Article keywords: ccna, certification, exam, distance, vector, command, meaning, review, ip, route, static, routing
Article Source: http://www.articles32.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, visit the website and download your free copies. You can also get FREE CCNA and CCNP exam questions every day! Get your CCNA study guide from The Bryant Advantage!
.: New Computer Certification Articles
1). Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address
To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this tutorial.
We've got two routers on a segment running HSRP, so first we need to find out what the MAC address of the HSRP virtual router is.
2). Cisco CCNP Certification / BSCI Exam Tutorial: An Introduction To BGP
When you're studying for the BSCI exam on the way to earning your CCNP certification, it's safe to say that BGP is like nothing you’ve studied to this point. BGP is an external routing protocol used primarily by Internet Service Providers (ISPs). Unless you work for an ISP today or in the future, you may have little or no prior exposure to BGP. Understanding BGP is a great addition to your skill set – and you have to know the basics well to pass the BSCI exam.
3). Cisco CCNA Certification Exam Tutorial: Distance Vector Command Review
Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very important distance vector and static routing commands you need to know, along with their proper usage and console output.
4). Cisco CCNA Certification Exam Tutorial: Keep Your Most Important Appointment
Imagine this. You have an appointment with a client to work on a server or router install. A few minutes before you're scheduled to be there, you decide there's something really good on TV you'd like to watch. Or you decide to go to the gym, or play a game, or do anything else except go see the client.
Even if you weren't going to get fired for not showing up, it's certainly unfair to the client.
5). CCNP Certification / BSCI Exam Tutorial: The BGP Neighbor Process
Like TCP, BGP is connection-oriented. An underlying connection between two BGP speakers is established before any routing information is exchanged. This connection takes place on TCP port 179. As with EIGRP and OSPF, keepalive messages are sent out by the BGP speakers in order to keep this relationship alive.
Once the connection is established, the BGP speakers exchange routes and synchronize their tables.
6). CCNP Certification / BCMSN Exam Tutorial: Server Load Balancing (SLB)
When you're working on your BCMSN exam on your way to CCNP certification, you'll read at length about how Cisco routers and multilayer switches can work to provide router redundancy - but there's another helpful service, Server Load Balancing, that does the same for servers. While HSRP, VRRP, and CLBP all represent multiple physical routers to hosts as a single virtual router, SLB represents multiple physical servers to hosts as a single virtual server.
7). CCNA / MCSE / CCNP Certification: Making Failure Work For You
Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're going to fail an exam. It's happened to almost all of us, yours truly included. What you have to keep in mind in these times is that success is not a straight line. You've probably seen charts showing the growth of an industry or a business -- you know, the ones that go from left to right, and look kind of jagged.
.: Top Computer Certification Articles
1). Cisco CCNP / BSCI Exam Tutorial: OSPF Route Redistribution Review
OSPF route redistribution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route redistribution basics.
To see if a router is an ABR or ASBR, run show ip ospf. This also displays any routes being redistributed into OSPF on this router.
2). Cisco CCNA Certification Exam Tutorial: Variance And Unequal Cost Load Balancing
To pass the CCNA exam, you've got to know how to work with IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure that all paths are in use while allowing for varying bandwidth rates.
Using the variance command is the easy part - it's getting the metric that's the hard part with IGRP.
3). Cisco CCNA Exam Tutorial: Route Summarization
Preparing to pass the CCNA exam and earn this important Cisco certification? Route summarization is just one of the many skills you'll have to master in order to earn your CCNA. Whether it's RIP version 2, OSPF, or EIGRP, the CCNA exam will demand that you can flawlessly configure route summarization.
Route summarization isn't just important for the CCNA exam.
4). Cisco CCNA / CCNP Home Lab Setup: How To Configure Reverse Telnet
Occasionally, during your CCNA and CCNP studies, you'll run into a term that just doesn't quite make sense to you. (Okay, more than occasionally!) One such term is "reverse telnet". As a Cisco certification candidate, you know that telnet is simply a protocol that allows you to remotely connect to a networking device such as a router or switch. But.
5). Cisco CCNA / CCNP Home Lab Tutorial: Configuring An Access Server
As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we'll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS.
Here's part of a configuration from one of my access servers:
ip host FRS 2006 100.
6). Cisco CCNA Certification: Defining Broadcast Domains
When you're studying to pass the CCNA exam and earn your certification, you're introduced to a great many terms that are either totally new to you or seem familiar, but you're not quite sure what they are. The term "broadcast domain" falls into the latter category for many CCNA candidates.
A broadcast domain is simply the group of end hosts that will receive a broadcast sent out by a given host.
7). Passing Your CCNA and CCNP: Configuring And Troubleshooting Router-On-A-Stick
For CCNA and CCNP candidates, it's hard not to laugh the first time you hear the phrase "router on a stick". Let's face it, that's a pretty silly term. But as those who have passed the CCNA and CCNP exams know, this is a vital exam topic that you must know how to configure and troubleshoot.
Basic Cisco theory states that for hosts in different VLANs to communicate, a Layer 3 device must be involved to handle the routing between the VLANs.