.: Cisco CCNA Exam Tutorial: Password Recovery Procedures
Category:Home / Computers / Computer Certification
It might happen on your CCNA exam, it might happen on your production network - but sooner or later, you're going to have to perform password recovery on a Cisco router or switch. This involves manipulating the router's configuration register, and that is enough to make some CCNA candidates and network administrators really nervous!
It's true that setting the configuration register to the wrong value can damage the router, but if you do the proper research before starting the password recovery process, you'll be fine.
Despite what some books say, there is no "one size fits all" approach to Cisco password recovery. What works on a 2500 router may not work on other routers and switches. There is a great master Cisco document out on the Web that you should bookmark today. Just put "cisco password recovery" in your favorite search engine and you should find it quickly.
The following procedure describes the process in recovering from a lost password on a Cisco 2500 router. As always, don't practice this at home. It is a good idea to get some practice with this technique in your CCNA / CCNP home lab, though!
The password recovery method examined here is for 2500 routers.
An engineer who finds themselves locked out of a router can view and change the password by changing the configuration register.
The router must first be rebooted and a “break” performed within the first 60 seconds of the boot process. This break sequence can also vary depending on what program is used to access the router, but
The router will now be in ROM Monitor mode. From the rom monitor prompt, change the default configuration register of 0x2102 to 0x2142 with the o/r 0x2142 command. Reload the router with the letter i. (As you can see, ROM Monitor mode is a lot different than working with the IOS!)
This particular config register setting will cause the router to ignore the contents of NVRAM. Your startup configuration is still there, but it will be ignored on reload.
When the router reloads, you’ll be prompted to enter Setup mode. Answer “N”, and type enable at the router> prompt.
Be careful here. Type configure memory or copy start run. Do NOT type write memory or copy run start!
Enter the command show running-config. You’ll see the passwords in either their encrypted or unencrypted format.
Type config t, then use the appropriate command to set a new enable secret or enable password.
Don’t forget to change the configuration register setting back to the original value! The command config-register 0x2102 will do the job. Save this change with write memory or copy run start, and then run reload one more time to restart the router.
This process sounds hard, but it's really not. You just have to be careful, particularly when you're copying the startup config over the running config. You don't want to get that backwards! So take your time, check the online Cisco documentation before starting, get some practice with this procedure with lab equipment, and you'll be ready for success on the CCNA exam and in your production network!
Article keywords: cisco, password, recovery, ccna, exam, tutorial, configuration, register, 2500, router, enable, ccie
Article Source: http://www.articles32.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, visit the website and download your free copies. You can also get FREE CCNA and CCNP exam questions every day! Get your CCNA study guide with The Bryant Advantage!
.: New Computer Certification Articles
1). Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address
To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this tutorial.
We've got two routers on a segment running HSRP, so first we need to find out what the MAC address of the HSRP virtual router is.
2). Cisco CCNP Certification / BSCI Exam Tutorial: An Introduction To BGP
When you're studying for the BSCI exam on the way to earning your CCNP certification, it's safe to say that BGP is like nothing you’ve studied to this point. BGP is an external routing protocol used primarily by Internet Service Providers (ISPs). Unless you work for an ISP today or in the future, you may have little or no prior exposure to BGP. Understanding BGP is a great addition to your skill set – and you have to know the basics well to pass the BSCI exam.
3). Cisco CCNA Certification Exam Tutorial: Distance Vector Command Review
Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very important distance vector and static routing commands you need to know, along with their proper usage and console output.
4). Cisco CCNA Certification Exam Tutorial: Keep Your Most Important Appointment
Imagine this. You have an appointment with a client to work on a server or router install. A few minutes before you're scheduled to be there, you decide there's something really good on TV you'd like to watch. Or you decide to go to the gym, or play a game, or do anything else except go see the client.
Even if you weren't going to get fired for not showing up, it's certainly unfair to the client.
5). CCNP Certification / BSCI Exam Tutorial: The BGP Neighbor Process
Like TCP, BGP is connection-oriented. An underlying connection between two BGP speakers is established before any routing information is exchanged. This connection takes place on TCP port 179. As with EIGRP and OSPF, keepalive messages are sent out by the BGP speakers in order to keep this relationship alive.
Once the connection is established, the BGP speakers exchange routes and synchronize their tables.
6). CCNP Certification / BCMSN Exam Tutorial: Server Load Balancing (SLB)
When you're working on your BCMSN exam on your way to CCNP certification, you'll read at length about how Cisco routers and multilayer switches can work to provide router redundancy - but there's another helpful service, Server Load Balancing, that does the same for servers. While HSRP, VRRP, and CLBP all represent multiple physical routers to hosts as a single virtual router, SLB represents multiple physical servers to hosts as a single virtual server.
7). CCNA / MCSE / CCNP Certification: Making Failure Work For You
Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're going to fail an exam. It's happened to almost all of us, yours truly included. What you have to keep in mind in these times is that success is not a straight line. You've probably seen charts showing the growth of an industry or a business -- you know, the ones that go from left to right, and look kind of jagged.
.: Top Computer Certification Articles
1). Cisco CCNP / BSCI Exam Tutorial: OSPF Route Redistribution Review
OSPF route redistribution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route redistribution basics.
To see if a router is an ABR or ASBR, run show ip ospf. This also displays any routes being redistributed into OSPF on this router.
2). Cisco CCNA Certification Exam Tutorial: Variance And Unequal Cost Load Balancing
To pass the CCNA exam, you've got to know how to work with IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure that all paths are in use while allowing for varying bandwidth rates.
Using the variance command is the easy part - it's getting the metric that's the hard part with IGRP.
3). Cisco CCNA Exam Tutorial: Route Summarization
Preparing to pass the CCNA exam and earn this important Cisco certification? Route summarization is just one of the many skills you'll have to master in order to earn your CCNA. Whether it's RIP version 2, OSPF, or EIGRP, the CCNA exam will demand that you can flawlessly configure route summarization.
Route summarization isn't just important for the CCNA exam.
4). Cisco CCNA / CCNP Home Lab Setup: How To Configure Reverse Telnet
Occasionally, during your CCNA and CCNP studies, you'll run into a term that just doesn't quite make sense to you. (Okay, more than occasionally!) One such term is "reverse telnet". As a Cisco certification candidate, you know that telnet is simply a protocol that allows you to remotely connect to a networking device such as a router or switch. But.
5). Cisco CCNA / CCNP Home Lab Tutorial: Configuring An Access Server
As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we'll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS.
Here's part of a configuration from one of my access servers:
ip host FRS 2006 100.
6). Cisco CCNA Certification: Defining Broadcast Domains
When you're studying to pass the CCNA exam and earn your certification, you're introduced to a great many terms that are either totally new to you or seem familiar, but you're not quite sure what they are. The term "broadcast domain" falls into the latter category for many CCNA candidates.
A broadcast domain is simply the group of end hosts that will receive a broadcast sent out by a given host.
7). Passing Your CCNA and CCNP: Configuring And Troubleshooting Router-On-A-Stick
For CCNA and CCNP candidates, it's hard not to laugh the first time you hear the phrase "router on a stick". Let's face it, that's a pretty silly term. But as those who have passed the CCNA and CCNP exams know, this is a vital exam topic that you must know how to configure and troubleshoot.
Basic Cisco theory states that for hosts in different VLANs to communicate, a Layer 3 device must be involved to handle the routing between the VLANs.