.: Cisco CCNP / BSCI Exam Tutorial: Using The OSPF Command “Area Range”
Category:Home / Computers / Computer Certification
Your BSCI and CCNP exam success depends on knowing the details, and one such detail is knowing the proper way to summarize routes in OSPF. Route summarization is not just a test of your binary conversion abilities, but knowing where and when to summarize routes. It will not surprise any CCNA or CCNP certification candidate that OSPF gives us the most options for route summarization, and therefore more details to know!
OSPF offers us two options for route summarization configurations. In a previous tutorial, we looked at the "summary-address" command, and today we'll look at the proper use of the "area range" command.
The "area range" command should be used on an Area Border Router (ABR) to summarize routes being advertised from one OSPF area to another. In this tutorial, R1 is acting as an ABR, with interfaces in both Area 0 and Area 1. Four loopbacks have been placed into R1's Area 1.
R1(config)#router ospf 1
R1(config-router)#network 12.0.0.0 0.255.255.255 a 1
R1(config-router)#network 13.0.0.0 0.255.255.255 a 1
R1(config-router)#network 14.0.0.0 0.255.255.255 a 1
R1(config-router)#network 15.0.0.0 0.255.255.255 a 1
The routing table of an OSPF neighbor, R2, shows all four routes.
R2#show ip route ospf
12.0.0.0/32 is subnetted, 1 subnets
O IA 12.12.12.12 [110/65] via 172.12.123.1, 00:18:52, Serial0
13.0.0.0/32 is subnetted, 1 subnets
O IA 13.13.13.13 [110/65] via 172.12.123.1, 00:18:42, Serial0
14.0.0.0/32 is subnetted, 1 subnets
O IA 14.14.14.14 [110/65] via 172.12.123.1, 00:18:32, Serial0
15.0.0.0/32 is subnetted, 1 subnets
O IA 15.15.15.15 [110/65] via 172.12.123.1, 00:18:32, Serial0
To keep the routing tables of downstream routers smaller but still have the desired IP connectivity, we can use the area range command on R1 to summarize these four routes. The key to keep in mind with the area range command is that the area number given in the command is the area containing the destinations, NOT the area that will receive the summary route.
R1(config)#router ospf 1
R1(config-router)#area 1 range 12.0.0.0 252.0.0.0
R2 now shows a single summary route that can be used to reach all four remote networks.
R2#show ip route ospf
O IA 12.0.0.0/6 [110/65] via 172.12.123.1, 00:00:21, Serial0
Interestingly enough, there's now an additional route in R1's routing table.
R1#show ip route ospf
O 12.0.0.0/6 is a summary, 00:07:53, Null0
When you configure summary routes in OSPF, a route to null0 will be installed into the OSPF routing table of the router performing the summarization. This helps to prevent routing loops. Any packets destined for the routes that have been summarized will have a longer match in the routing table, and packets that do not match one of the summarized routes but do match the summary route will be dropped.
Article keywords: Ccnp, ccna, bsci, exam, tutorial, ospf, summary, route, summarization, area, range, address, command, null, free, Bryant, advantage, 12933, chris
Article Source: http://www.articles32.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNP and CCNA tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, just visit the website! You can also get FREE CCNA and CCNP exam questions every day! Pass the CCNP exam with The Bryant Advantage!
.: New Computer Certification Articles
1). Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address
To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this tutorial.
We've got two routers on a segment running HSRP, so first we need to find out what the MAC address of the HSRP virtual router is.
2). Cisco CCNP Certification / BSCI Exam Tutorial: An Introduction To BGP
When you're studying for the BSCI exam on the way to earning your CCNP certification, it's safe to say that BGP is like nothing you’ve studied to this point. BGP is an external routing protocol used primarily by Internet Service Providers (ISPs). Unless you work for an ISP today or in the future, you may have little or no prior exposure to BGP. Understanding BGP is a great addition to your skill set – and you have to know the basics well to pass the BSCI exam.
3). Cisco CCNA Certification Exam Tutorial: Distance Vector Command Review
Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very important distance vector and static routing commands you need to know, along with their proper usage and console output.
4). Cisco CCNA Certification Exam Tutorial: Keep Your Most Important Appointment
Imagine this. You have an appointment with a client to work on a server or router install. A few minutes before you're scheduled to be there, you decide there's something really good on TV you'd like to watch. Or you decide to go to the gym, or play a game, or do anything else except go see the client.
Even if you weren't going to get fired for not showing up, it's certainly unfair to the client.
5). CCNP Certification / BSCI Exam Tutorial: The BGP Neighbor Process
Like TCP, BGP is connection-oriented. An underlying connection between two BGP speakers is established before any routing information is exchanged. This connection takes place on TCP port 179. As with EIGRP and OSPF, keepalive messages are sent out by the BGP speakers in order to keep this relationship alive.
Once the connection is established, the BGP speakers exchange routes and synchronize their tables.
6). CCNP Certification / BCMSN Exam Tutorial: Server Load Balancing (SLB)
When you're working on your BCMSN exam on your way to CCNP certification, you'll read at length about how Cisco routers and multilayer switches can work to provide router redundancy - but there's another helpful service, Server Load Balancing, that does the same for servers. While HSRP, VRRP, and CLBP all represent multiple physical routers to hosts as a single virtual router, SLB represents multiple physical servers to hosts as a single virtual server.
7). CCNA / MCSE / CCNP Certification: Making Failure Work For You
Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're going to fail an exam. It's happened to almost all of us, yours truly included. What you have to keep in mind in these times is that success is not a straight line. You've probably seen charts showing the growth of an industry or a business -- you know, the ones that go from left to right, and look kind of jagged.
.: Top Computer Certification Articles
1). Cisco CCNP / BSCI Exam Tutorial: OSPF Route Redistribution Review
OSPF route redistribution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route redistribution basics.
To see if a router is an ABR or ASBR, run show ip ospf. This also displays any routes being redistributed into OSPF on this router.
2). Cisco CCNA Certification Exam Tutorial: Variance And Unequal Cost Load Balancing
To pass the CCNA exam, you've got to know how to work with IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure that all paths are in use while allowing for varying bandwidth rates.
Using the variance command is the easy part - it's getting the metric that's the hard part with IGRP.
3). Cisco CCNA Exam Tutorial: Route Summarization
Preparing to pass the CCNA exam and earn this important Cisco certification? Route summarization is just one of the many skills you'll have to master in order to earn your CCNA. Whether it's RIP version 2, OSPF, or EIGRP, the CCNA exam will demand that you can flawlessly configure route summarization.
Route summarization isn't just important for the CCNA exam.
4). Cisco CCNA / CCNP Home Lab Setup: How To Configure Reverse Telnet
Occasionally, during your CCNA and CCNP studies, you'll run into a term that just doesn't quite make sense to you. (Okay, more than occasionally!) One such term is "reverse telnet". As a Cisco certification candidate, you know that telnet is simply a protocol that allows you to remotely connect to a networking device such as a router or switch. But.
5). Cisco CCNA / CCNP Home Lab Tutorial: Configuring An Access Server
As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we'll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS.
Here's part of a configuration from one of my access servers:
ip host FRS 2006 100.
6). Cisco CCNA Certification: Defining Broadcast Domains
When you're studying to pass the CCNA exam and earn your certification, you're introduced to a great many terms that are either totally new to you or seem familiar, but you're not quite sure what they are. The term "broadcast domain" falls into the latter category for many CCNA candidates.
A broadcast domain is simply the group of end hosts that will receive a broadcast sent out by a given host.
7). Passing Your CCNA and CCNP: Configuring And Troubleshooting Router-On-A-Stick
For CCNA and CCNP candidates, it's hard not to laugh the first time you hear the phrase "router on a stick". Let's face it, that's a pretty silly term. But as those who have passed the CCNA and CCNP exams know, this is a vital exam topic that you must know how to configure and troubleshoot.
Basic Cisco theory states that for hosts in different VLANs to communicate, a Layer 3 device must be involved to handle the routing between the VLANs.