.: Passing The Cisco CCNA Exam: An Illustrated Guide To Router Modes
Category:Home / Computers / Computer Certification
When you're getting started on your CCNA studies, learning the different router modes is key to passing your Intro and ICND exams. But keeping those modes straight can be very difficult. (At least it was for me!) Let's take a look at the various router modes you'll need to know about to pass your CCNA, and use IOS Help to illustrate the different uses of each mode.
The first mode you'll see on a router (if the person before you logged off as they should have) is user exec mode. This is also the default mode a user is placed into when using Telnet to connect to a router. The prompt will look like this:
R1>
You can't write or add to a configuration in this mode, but you can run quite a few show commands. This is a good mode to have users in who need to see the configuration, but shouldn't be allowed to change it.
To get to the next level, type enable at the user exec prompt:
R1>enable
R1#
Notice that the prompt changed. This mode has two names, the official one being privileged exec mode. It's more commonly referred to as enable mode, since "enable" is what you type to get into this mode.
This mode gives you more options for show and other commands, but you still can't configure anything. To configure global commands, use "configure terminal", or "conf t", to enter global configuration mode.
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#
The prompt has changed again, and now global configuration commands such as hostname and no ip domain-lookup can be entered.
From here, you've got a lot of options, but we'll look at three you need to know for your CCNA exams. To apply configuration commands to an interface, enter interface configuration mode, as shown here:
R1(config)#interface serial0
R1(config-if)#
You must be in global config mode to get into interface config mode you cannot go from enable mode straight to interface configuration mode.
R1#interface serial0
^
% Invalid input detected at '^' marker.
Interface configuration mode allows you to apply an IP address to the interface, as well as many other commands related to frame relay, ISDN, and dynamic routing protocols.
For the CCNA, you need to know about two other configuration modes. To configure console commands (such as password protection), enter line configuration mode as shown here:
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#line console 0
R1(config-line)#password cisco
R1(config-line)#login
The prompt "(config-line)" indicates that you're in line configuration mode. Your console line is not the only line you'll be configuring for the CCNA, though your vty lines are used for incoming telnet connections and must be configured in a similar fashion.
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#line console 0
R1(config-line)#password cisco
R1(config-line)#login
R1(config-line)#line vty 0 4
R1(config-line)#password cisco
R1(config-line)#login
Notice that you do not have to exit one interface mode to go to another one. Let's say that you've configured your vty lines and now want to put an IP address on your Ethernet interface. You don't have to go out with ctrl-z and then start again you can go straight to interface config mode from line config mode. Just make sure you see the prompt change!
R1(config-line)#line vty 0 4
R1(config-line)#password cisco
R1(config-line)#login
R1(config-line)#interface ethernet0
R1(config-if)#ip address 15.1.1.1 255.255.255.0
When you're preparing for CCNA exam success, there's a lot to absorb. Just take it one piece at a time, get some hands-on experience to go with your theory, and before you know it you're moving around in the different Cisco router configuration modes without giving it a second thought. Keep studying and your CCNA exam success is assured!
Article keywords: ccna, free, ccnp, pass, exam, certification, icnd, interface, password, router, switch, cisco, mcse
Article Source: http://www.articles32.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of FREE CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages. Video courses and training, binary and subnetting help, and corporate training are also available.
For a FREE copy of his latest e-books, "How To Pass The CCNA" or "How To Pass The CCNP", send a request to chris@thebryantadvantage.com today !
.: New Computer Certification Articles
1). Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address
To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this tutorial.
We've got two routers on a segment running HSRP, so first we need to find out what the MAC address of the HSRP virtual router is.
2). Cisco CCNP Certification / BSCI Exam Tutorial: An Introduction To BGP
When you're studying for the BSCI exam on the way to earning your CCNP certification, it's safe to say that BGP is like nothing you’ve studied to this point. BGP is an external routing protocol used primarily by Internet Service Providers (ISPs). Unless you work for an ISP today or in the future, you may have little or no prior exposure to BGP. Understanding BGP is a great addition to your skill set – and you have to know the basics well to pass the BSCI exam.
3). Cisco CCNA Certification Exam Tutorial: Distance Vector Command Review
Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very important distance vector and static routing commands you need to know, along with their proper usage and console output.
4). Cisco CCNA Certification Exam Tutorial: Keep Your Most Important Appointment
Imagine this. You have an appointment with a client to work on a server or router install. A few minutes before you're scheduled to be there, you decide there's something really good on TV you'd like to watch. Or you decide to go to the gym, or play a game, or do anything else except go see the client.
Even if you weren't going to get fired for not showing up, it's certainly unfair to the client.
5). CCNP Certification / BSCI Exam Tutorial: The BGP Neighbor Process
Like TCP, BGP is connection-oriented. An underlying connection between two BGP speakers is established before any routing information is exchanged. This connection takes place on TCP port 179. As with EIGRP and OSPF, keepalive messages are sent out by the BGP speakers in order to keep this relationship alive.
Once the connection is established, the BGP speakers exchange routes and synchronize their tables.
6). CCNP Certification / BCMSN Exam Tutorial: Server Load Balancing (SLB)
When you're working on your BCMSN exam on your way to CCNP certification, you'll read at length about how Cisco routers and multilayer switches can work to provide router redundancy - but there's another helpful service, Server Load Balancing, that does the same for servers. While HSRP, VRRP, and CLBP all represent multiple physical routers to hosts as a single virtual router, SLB represents multiple physical servers to hosts as a single virtual server.
7). CCNA / MCSE / CCNP Certification: Making Failure Work For You
Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're going to fail an exam. It's happened to almost all of us, yours truly included. What you have to keep in mind in these times is that success is not a straight line. You've probably seen charts showing the growth of an industry or a business -- you know, the ones that go from left to right, and look kind of jagged.
.: Top Computer Certification Articles
1). Cisco CCNP / BSCI Exam Tutorial: OSPF Route Redistribution Review
OSPF route redistribution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route redistribution basics.
To see if a router is an ABR or ASBR, run show ip ospf. This also displays any routes being redistributed into OSPF on this router.
2). Cisco CCNA Certification Exam Tutorial: Variance And Unequal Cost Load Balancing
To pass the CCNA exam, you've got to know how to work with IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure that all paths are in use while allowing for varying bandwidth rates.
Using the variance command is the easy part - it's getting the metric that's the hard part with IGRP.
3). Cisco CCNA Exam Tutorial: Route Summarization
Preparing to pass the CCNA exam and earn this important Cisco certification? Route summarization is just one of the many skills you'll have to master in order to earn your CCNA. Whether it's RIP version 2, OSPF, or EIGRP, the CCNA exam will demand that you can flawlessly configure route summarization.
Route summarization isn't just important for the CCNA exam.
4). Cisco CCNA / CCNP Home Lab Setup: How To Configure Reverse Telnet
Occasionally, during your CCNA and CCNP studies, you'll run into a term that just doesn't quite make sense to you. (Okay, more than occasionally!) One such term is "reverse telnet". As a Cisco certification candidate, you know that telnet is simply a protocol that allows you to remotely connect to a networking device such as a router or switch. But.
5). Cisco CCNA / CCNP Home Lab Tutorial: Configuring An Access Server
As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we'll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS.
Here's part of a configuration from one of my access servers:
ip host FRS 2006 100.
6). Cisco CCNA Certification: Defining Broadcast Domains
When you're studying to pass the CCNA exam and earn your certification, you're introduced to a great many terms that are either totally new to you or seem familiar, but you're not quite sure what they are. The term "broadcast domain" falls into the latter category for many CCNA candidates.
A broadcast domain is simply the group of end hosts that will receive a broadcast sent out by a given host.
7). Passing Your CCNA and CCNP: Configuring And Troubleshooting Router-On-A-Stick
For CCNA and CCNP candidates, it's hard not to laugh the first time you hear the phrase "router on a stick". Let's face it, that's a pretty silly term. But as those who have passed the CCNA and CCNP exams know, this is a vital exam topic that you must know how to configure and troubleshoot.
Basic Cisco theory states that for hosts in different VLANs to communicate, a Layer 3 device must be involved to handle the routing between the VLANs.